Thermoplastic Oil Aging: 39 Percent Uptake

Thermoplastic oil aging at 95 degrees C pushed mass uptake to about 39 percent in injection-molded polypropylene tensile specimens and cut tensile modulus retention to roughly 34 percent, while an impact-modified polyphenylene sulfide grade held or improved its tensile properties. At room temperature the same materials stayed below 1 percent uptake. Here is what that temperature split means for a formulator judging migration resistance in a cable or pipe compound.

Why this matters in pipe and cable compounds

Thermoplastic compounds used for pipe and cable service are often specified on short-term mechanical data and then asked to survive decades of contact with oils, fuels and process fluids. Fluid uptake is the quiet failure route. A compound can absorb a reference oil, swell, lose stiffness and still look intact on a visual inspection. By the time a tensile test shows the loss, the part has already changed dimension and load-bearing capacity.

That's where migration resistance enters the formulation logic. A compound carries small molecules by design: plasticizers for flexibility, compatibilizers and coupling agents for filler and blend interfaces, stabilizers for processing and service. Whether those molecules stay in the compound under heat and fluid contact is partly the same transport problem as whether an external fluid gets in. A formulation that takes up a lot of oil is also a formulation whose internal additive balance is being challenged.

This is a link, not a claim about the study. The work behind this article measured mass uptake and mechanical retention in three commercial pipe-grade thermoplastics immersed in a standard reference oil. No plasticizer, compatibilizer, coupling agent or proprietary additive grade was tested, and no additive formulation was varied. The numbers below are industry-level evidence about how a polyolefin and a high-performance thermoplastic behave under hot oil exposure, not performance data for any supplied additive.

Methods and reported conditions

Item

Value

What it controls

Materials

Polypropylene impact copolymer (PP), polyethylene of raised temperature (PERT), impact-modified polyphenylene sulfide (PPS)

Three resin classes for pipe fabrication

Fabrication routes

Injection molding and extrusion

Processing history

Fluid

IRM 902 reference oil

Aging medium

Temperatures

Room temperature and 95 degrees C

Service versus accelerated condition

Mass uptake

Measured gravimetrically

Fluid absorption

Mechanical tests

Tensile testing and in situ punch-shear testing

Property retention

Punch diameter

25.4 mm

Punch-shear geometry

Thermal analysis

Differential scanning calorimetry

Crystallinity and transitions

Chemical analysis

Fourier-transform infrared spectroscopy

New absorption bands

Oil composition

C30+ fraction 62.003 percent, C20-C29 fraction 37.275 percent

What it indicates about the aging medium

The challenge fluid in this thermoplastic oil aging study was characterized by gas chromatography with flame ionization detection. The predominance of C20 and heavier material, including a method-defined C30+ residue of 62.003 percent, distinguishes it from lighter hydrocarbon fluids. That matters for interpretation: a heavy, high-boiling oil behaves differently from a light solvent, and uptake numbers from this medium shouldn't be transferred to every service fluid.

Property retention was calculated as 100 times the ratio of the aged group mean to the corresponding unaged group mean. The authors note that aged tensile and punch-shear retentions weren't directly comparable because tensile tests were performed ex situ, whereas the 95 degrees C punch-shear tests were conducted in situ. That limitation is stated in the source itself and it constrains how the two data sets can be combined.

What thermoplastic oil aging looks like at two temperatures

Condition

Mass uptake

Mechanical-property retention

Reported reading

Room temperature, all materials

Below 1 percent

89 to 113 percent

Minor changes only

95 degrees C, injection-molded PP tensile specimens

Approximately 39 percent

Tensile modulus retention approximately 34 to 36 percent

Largest uptake and largest loss

95 degrees C, injection-molded PP punch-shear coupons

Approximately 23 percent

Not stated at this level

Geometry effect

95 degrees C, extruded PP tensile and punch-shear coupons

Approximately 20 percent

Not stated at this level

Fabrication route effect

95 degrees C, PERT

Intermediate

Tensile modulus retention approximately 60 to 74 percent

Moderate sensitivity

95 degrees C, PPS

Negligible

Tensile modulus and yield-strength retention approximately 123 to 139 percent

Highest resistance

The temperature split's the headline of thermoplastic oil aging at these two conditions. Below 1 percent uptake at room temperature with retention scattered between 89 and 113 percent is essentially a no-change result. At 95 degrees C the polypropylene absorbs roughly 39 percent of its mass in oil and loses about two-thirds of its tensile modulus. A qualification run only at ambient conditions would miss the entire failure regime.

The spread within polypropylene is also informative. Injection-molded tensile specimens reached about 39 percent, injection-molded punch-shear coupons about 23 percent, and extruded coupons about 20 percent. Same resin, same oil, same temperature, different geometry and fabrication route. That's a warning about using a single coupon shape to set a fluid-resistance specification.

The authors also report localized blister-like or dotted surface regions on the aged polypropylene, suggesting that the measured mass increase included contributions from surface swelling and near-surface oil accumulation, rather than being solely demonstrated as bulk absorption. They explicitly frame that as a contributing interpretation, not as the sole demonstrated cause. Any calculation that treats the full 39 percent as uniformly distributed through the part would be going beyond the source.

Detailed retention numbers at 95 degrees C

Material and property

Baseline mean +/- SD, MPa

Aged mean +/- SD, MPa

Retention, percent

PP tensile modulus

337.24 +/- 9.58

115.01 +/- 4.12

34.1

PP tensile yield strength

8.50 +/- 0.19

4.12 +/- 0.06

48.5

PP apparent shear modulus

42.81 +/- 3.42

22.93 +/- 4.08

53.6

PP punch-shear yield strength

4.65 +/- 0.28

4.21 +/- 0.45

90.4

PP extruded tensile modulus

293.74 +/- 17.46

106.21 (SD not given in available text)

Not stated

The tensile modulus fell from 337.24 to 115.01 MPa, a loss of more than 220 MPa in absolute terms, while punch-shear yield strength retained 90.4 percent. Those two numbers come from the same aged material under different loading modes. A specification built on one test would give a very different picture from one built on the other, and the source itself warns that the aged retentions aren't directly comparable because of the ex situ versus in situ test difference.

Baseline punch-shear yield strength correlated strongly with tensile yield strength, which supports its use as a complementary indicator. The authors also note noticeable scatter in the apparent shear modulus relationship, especially among lower-modulus data points and between fabrication routes. That scatter is attributed to compliance and local deformation constraint effects rather than to a systematic material difference.

Crystallinity moved differently by route. Injection-molded PPS went from 17.6 to 28.7 percent, with the cold-crystallization transition disappearing, consistent with thermal conditioning and additional crystalline ordering during prolonged exposure at 95 degrees C. Extruded PPS went the other way, from 31.3 to 25.1 percent, while its tensile modulus and yield-strength retention stayed above baseline. The authors state that the improved mechanical retention of the PPS-based specimens therefore can't be attributed to crystallinity alone. That's a deliberate self-limitation and it should be carried into any reading of the result.

Fourier-transform infrared spectroscopy showed no major new absorption bands after aging. In other words, the property loss wasn't accompanied by a clearly detectable new chemical species in that measurement, which points toward physical absorption and morphological change rather than a resolved chemical degradation route. The source doesn't claim to have excluded all chemical change.

Where migration resistance fits in a compound specification

In a thermoplastic oil aging context, migration resistance is the tendency of small molecules in a compound to stay where they were put under heat, fluid contact and time. In a flexible PVC or polyolefin cable compound, a plasticizer is chosen partly for low migration and low extraction; a phthalate-free option is often selected for compliance reasons. In a filled polypropylene compound, a compatibilizer or coupling agent is chosen for interfacial adhesion and filler dispersion. Both decisions assume the additive stays in the formulation.

The oil-aging data make one general point that transfers: a polyolefin can take up a very large amount of a hydrocarbon fluid at elevated temperature while a higher-performance thermoplastic takes up almost none, under identical exposure. Any small molecule in the compound partitions between the polymer, any filler or interface, and the free volume of the network. A matrix that admits 39 percent oil is a matrix whose internal partitioning is being rewritten. That's a mechanism worth testing when migration resistance is the target, but it isn't a measurement of migration.

The same caution applies to plasticizer selection. The study didn't compare plasticizer chemistries, didn't measure extraction loss and didn't test a plasticized compound. What it does show is that fluid uptake and mechanical retention move together at 95 degrees C, and that fabrication route changes the magnitude. A compounder specifying migration resistance should measure it on the actual compound, on the actual geometry, at the actual service temperature, rather than infer it from resin-level uptake data.

There's also a process reading in thermoplastic oil aging. Injection-molded and extruded specimens of the same resin absorbed different amounts of oil. Processing history sets morphology, and morphology sets transport. For an additive supplier, that means a loading recommendation can't be separated from how the customer converts the compound.

The counterintuitive result

The counterintuitive part is that the highest-performing material gained mechanical properties. PPS specimens retained or exceeded their unaged tensile properties, with tensile modulus and yield-strength retention reaching approximately 123 to 139 percent, while absorbing negligible oil. A hot-oil aging program normally produces losses, and the usual mental model is that the best outcome is a small loss.

The second surprise is that the extruded PPS went from 31.3 to 25.1 percent crystallinity while still improving its tensile retention. Crystallinity and stiffness usually track together, so a drop in crystallinity alongside a gain in modulus retention breaks the expected direction. The authors explicitly say the improved retention of the PPS-based specimens can't be attributed to crystallinity alone, and they don't provide a resolved alternative mechanism in the reported analysis. That's an open question, not a conclusion to be borrowed.

A third, quieter point: the polypropylene lost about two-thirds of its tensile modulus but kept 90.4 percent of its punch-shear yield strength. Total fluid uptake and total property loss aren't single numbers. A compound qualified on one metric can look acceptable while another metric has collapsed, which is the same failure mode as a total volatiles measurement that hides which species remain.

What to check before you scale a formulation

  • Run fluid aging at the actual service temperature. Room temperature gave below 1 percent uptake and 89 to 113 percent retention; 95 degrees C gave about 39 percent uptake and roughly 34 percent modulus retention.
  • Test more than one coupon geometry and fabrication route. Injection-molded tensile specimens, injection-molded punch-shear coupons and extruded coupons gave about 39, 23 and 20 percent uptake.
  • Don't combine tensile and punch-shear retentions as if they were equivalent. The source states the aged retentions weren't directly comparable because of ex situ versus in situ testing.
  • Measure migration and extraction on the finished compound. No plasticizer or additive grade was tested in this study.
  • Treat the 39 percent uptake as a mass increase with possible surface contributions, not as uniformly distributed bulk absorption. The source flags surface swelling and near-surface oil accumulation as contributing interpretations.
  • Keep Fourier-transform infrared results in their lane. No major new absorption bands were reported, which isn't proof that no chemical change occurred.

Limitations and what the data do not prove

The source is an open access article under a CC BY-NC-ND licence, which restricts commercial reuse. Full text and tables were available for this write-up. It's a laboratory immersion study on three pipe-grade thermoplastics, not a compounding trial. No plasticizer, phthalate-free plasticizer, compatibilizer, coupling agent, filler or commercial additive grade was tested, and no additive formulation was varied. The link to migration resistance is a formulation principle drawn from industry-level evidence about fluid transport in polyolefins.

Only two temperatures, one reference oil and three resin systems were studied, with two fabrication routes. The authors state that aged tensile and punch-shear retentions weren't directly comparable because tensile tests were performed ex situ while the 95 degrees C punch-shear tests were conducted in situ. They also note that the measured mass increase may have included surface swelling and near-surface oil accumulation rather than being solely demonstrated as bulk absorption, and that the improved mechanical retention of the PPS-based specimens can't be attributed to crystallinity alone. These are the authors' own qualifications and they bound every number above.

There's no service-life model, no long-term extrapolation, no cycling, no additive loss measurement and no measurement of how the reference oil interacts with a plasticized or filled compound. Fourier-transform infrared spectroscopy showed no major new absorption bands, which doesn't exclude all chemical change. None of the coefficients or retention values should be used as a specification figure for a compound or an additive. Any claim about a specific formulation would need its own aging, migration and extraction program on the actual geometry and resin.

Bottom line

Thermoplastic oil aging at 95 degrees C separated the three materials sharply: polypropylene took up about 39 percent oil and retained roughly 34 percent of its tensile modulus, PERT was intermediate, and PPS showed negligible uptake with 123 to 139 percent tensile retention. Geometry and fabrication route changed the polypropylene uptake from about 39 to 20 percent. For a compounder the transferable lesson concerns migration resistance: measure fluid transport and property retention on the finished compound at service temperature, and treat total uptake as a starting point rather than a mechanism.

FAQ

What is thermoplastic oil aging in this study?

It is the immersion of injection-molded and extruded specimens of a polypropylene impact copolymer, a polyethylene of raised temperature grade and an impact-modified polyphenylene sulfide grade in IRM 902 reference oil at room temperature and 95 degrees C. Mass uptake, tensile testing, in situ punch-shear testing, differential scanning calorimetry and Fourier-transform infrared spectroscopy were used to evaluate fluid absorption, mechanical-property retention and thermal and chemical changes.

How large was the temperature effect?

At room temperature, mass uptake stayed below 1 percent and mechanical-property retention ranged from 89 to 113 percent across the materials, fabrication routes and testing methods. At 95 degrees C, injection-molded polypropylene tensile specimens reached approximately 39 percent mass uptake and retained only approximately 34 to 36 percent of their tensile modulus. The authors describe the room-temperature deviations as smaller in magnitude than the losses at 95 degrees C.

Which material resisted the oil best?

The impact-modified polyphenylene sulfide grade showed negligible mass uptake and stable or improved mechanical-property retention, with tensile modulus and tensile yield-strength retention reaching approximately 123 to 139 percent. Polyethylene of raised temperature showed intermediate behavior, with tensile modulus retention of approximately 60 to 74 percent. Polypropylene showed the greatest uptake and the largest tensile-property reduction. The source ranks PPS highest, followed by PERT and PP.

Was a plasticizer or compatibilizer tested in this study?

No. The study tested three pipe-grade thermoplastics in a reference oil. No plasticizer, phthalate-free plasticizer, compatibilizer, coupling agent, filler or commercial additive grade appears in the work, and no additive formulation was varied. The discussion of migration resistance is a formulation principle about how small molecules move through a polymer matrix, not a measurement of any supplied additive.

Do the mass uptake data prove plasticizer migration?

No. Mass uptake measures how much external fluid enters the specimen. Migration and extraction measure how much of an internal additive leaves it. The reported work gives no plasticizer loss, extraction or volatility data. The oil-aging results are relevant as industry-level evidence about fluid transport in these resins, but a permanence claim for a compound would need a dedicated migration and extraction program on the finished formulation.

Why did different polypropylene coupons absorb different amounts?

Injection-molded tensile specimens reached approximately 39 percent, injection-molded punch-shear coupons approximately 23 percent, and extruded tensile and punch-shear coupons approximately 20 percent. The source reports these differences without resolving a single cause, and it notes that fabrication route and coupon geometry both matter. Processing history sets morphology, and morphology sets transport, but no quantitative morphology analysis is given to assign the split.

What do the detailed retention numbers show?

For polypropylene at 95 degrees C, tensile modulus fell from 337.24 +/- 9.58 to 115.01 +/- 4.12 MPa, a retention of 34.1 percent. Tensile yield strength fell from 8.50 +/- 0.19 to 4.12 +/- 0.06 MPa, retention 48.5 percent. Apparent shear modulus fell from 42.81 +/- 3.42 to 22.93 +/- 4.08 MPa, retention 53.6 percent. Punch-shear yield strength went from 4.65 +/- 0.28 to 4.21 +/- 0.45 MPa, retention 90.4 percent.

Can tensile and punch-shear retentions be compared directly?

No. The authors state that aged tensile and punch-shear retentions were not directly comparable because tensile tests were performed ex situ, whereas the 95 degrees C punch-shear tests were conducted in situ. Baseline punch-shear yield strength did correlate strongly with tensile yield strength, which supports its use as a complementary indicator, but the scatter in the apparent shear modulus relationship was noticeable, especially among lower-modulus data points and between fabrication routes.

What happened to crystallinity during aging?

For injection-molded PPS, blend crystallinity increased from 17.6 to 28.7 percent and the cold-crystallization transition disappeared, consistent with thermal conditioning and additional crystalline ordering at 95 degrees C. Extruded PPS went from 31.3 to 25.1 percent while retaining or improving its tensile properties. The authors state that the improved mechanical retention of the PPS-based specimens therefore cannot be attributed to crystallinity alone.

Did the oil cause chemical degradation?

Fourier-transform infrared spectroscopy showed no major new absorption bands after aging, so no clearly detectable new chemical species appeared in that measurement. The source does not claim this excludes all chemical change. It also notes localized blister-like or dotted surface regions on aged polypropylene, suggesting the measured mass increase included contributions from surface swelling or near-surface oil accumulation, which the authors present as a contributing interpretation rather than the sole demonstrated cause.

What is the single most useful change to a fluid-resistance specification?

Test at service temperature on the actual coupon geometry and record more than one mechanical mode. Room temperature gave below 1 percent uptake and near-baseline retention, while 95 degrees C gave about 39 percent uptake and roughly 34 percent modulus retention in the same resin. A single ambient-condition qualification would miss the entire regime where the compound fails, and a single mechanical metric would hide the fact that punch-shear yield strength still retained 90.4 percent. 

Comments

Popular posts from this blog

Odor Counteraction Explained: Beyond Simple Removal

Triacetin Plasticized Film: Water and Strength

Amorphous Polyarylate: Properties, Cost and Global Supply